Lutz Pumps Accessories for Hazardous Duty

1. Bonding wire 2. Ground wire 3. Conductive hose, (106 Ohms) 4. Conductive fitting of hose into hose     connector 5. Metal pump tube for zone "0" in Stainless     Steel or Hastelloy C 6. Explosion proof motor Lutz Silver Star or     MD-1/MD-2 (Ex) Air-Motor 7. Nozzle Stainless Steel or Brass 8. Flow control system (Ex) 9. Emission proof fume barrier

Bonding is the electrical interconnection between containers (such as a drum and a receiving can). Bonding must be completed before pumping begins. For better conductivity paint and dirt shall be removed from the contact points.

Grounding is the electrical connection between a container and a "constant ground". A "constant ground" would be a metal pipe (water pipe) or rod in contact with the earth. An underground tank and piping connected to it would be inherently grounded by nature of the installation.

Both Bonding and Grounding of containers of flammable liquids are required under U.S. Government OSHA regulations and National Fire Protection Association Code 77, static electricity

Metal pumps in stainless steel or Hastelloy C and pump motor must be bonded to metal container or grounded, if used with plastic container. Normal safety procedures must be used at all times when operating any piece of machinery.

			Specification	Order No.
	Ground and Bonding Wire Serves to create electrically conductive connection between explosion proof pump and container as earthing and equipotential bonding function.		Ground Wire 6' Bonding Wire 10'	0204-994 0204-995
	Electrically Conductive Hoses Caution: Electrical conductivity is assured through the use of break resistant textile copper threads in the rubber coating. If correctly installed, resistance during the entire life of these will remain below 106 ohms.
	Stainless Steel Nozzle Ideally suitable for filling and transferring liquids in food and pharmaceutical industries. Stainless steel 316 housing and valve tappet FPM (Vitron®) seals. Additional costs for EPDM or Vitron®/FEP seals. Other seals on request Available with male thread 1".	Operating pressure: max. 43.5 psi Viscosity: max. 760 cps Rate of  flow: max. 13.2 GPM (water) Temperature of  medium: max. 176 ºF Weight: approx. 2.2 lbs Connection: hose barb 3/4" 0204-689 hose barb 1" 0204-699 hose barb 1 1/4" 0204-700 male thread 1" 0204-730
	Brass Nozzle With Turning Knuckle Brass housing and valve tappet. PTFE seals. For filling and transferring solvents and neutral liquids.	Operating pressure: max. 58  psi Viscosity: max. 760 cps Rate of  flow: max. 21.1 GPM (water) Temperature of  medium: max. 176 ºF Weight: approx. 1.32 lbs Connection: female thread 1" 0372-498
	Modular Electrical Flow Control System For metering all kinds of liquids. Wide range of applications: Directly at the drum pump, remote or in-line operation possible. Convenient presetting of required volume using a numerical keypad. A comprehensive range of system components offers practical problem solutions. Two standard and three explosion proof meter versions are available.
	Emission Proof Fume Barrier To prevent emission of dangerous gasses when using a drum pump, thus protecting the operator, the environment, and the drive motor from hazardous, aggressive gasses and vapors. Two venting valves ensure pressure compensation inside and outside the drum. Connection for gas displacement pipe: 3/8" female Seals: Vitron® as standard. Other threads and seal materials on request.		Material: brass stainless steel Pump tube diameter: 1.62 inches 1.62 inches 0204-252 0204-253

	Reducer To connect quick connect/disconnect hose coupling with pump tube. female thread 1-1/4" and 1"	Material: Stainless steel	0372-019
	Quick-Action Hose Coupling Male Adapter	in stainless steel, male 1"	0372-024
	Female Hose Couplings Ensure rapid, leakproof connection between pump and hose. Available in stainless steel and polypropylene.	in stainless steel, female 1", seal FEP/EDPM	0372-025

	Emission Proof Fume Barrier To prevent emission of dangerous gasses when using a drum pump, thus protecting the operator, the environment, and the drive motor from hazardous, aggressive gasses and vapors. Two venting valves ensure pressure compensation inside and outside the drum. Connection for gas displacement pipe: 3/8" female Seals: Vitron® as standard. Other threads and seal materials on request.	Material: Pump tube diameter: brass 1.62 inches 0204-252 stainless steel 1.62 inches 0204-253
	Foot Strainers Available in PP, brass, and stainless steel, for mounting on the pump foot. Prevents impurities from entering the pump.	Material: pump tube: brass Alu dia. 41 mm, SS dia 41 mm 0204-633 stainless steel HC dia 38 mm 0204-632 stainless steel SS dia. 41 mm 0204-617 stainless steel B70V 0204-802
	Discharge Spouts For transfer liquids to other vessels. Available in PP, aluminum, and stainless steel. Spouts are connected onto the pump's discharge.	Material: nominal diameter: wing nut: SS 1" 1-1/4" 0204-225 SS 1-1/2" (for B70V) 1-1/4" 0204-226