July 2, 2008

Custom Control Panels, Temperature Control Panels
For a wide variety of applications, manufactured by Heaters Controls And Sensors custom control panels, temperature control panels that are needed to operate in 60ºC environments, to laboratory controllers that are to maintain temperatures within +/- 0.01ºC.

These custom control panels, temperature control panels could be made to withstand washdowns with corrosive chemicals with all components on the panel conforming to IP 65 and NEMA 4X. Integration of components for steam booster heaters or recirculation heaters with flow fail safe interlocks are also available.
>> Learn More | >> Request Information

Aqua-Boy Moisture Meter
Aqua-Boy Moisture Meter measures the moisture content of many solid materials quickly and accurately. It provides a direct read-out of percent moisture in seconds. The extensive selection of probes available suits the Aqua-Boy Moisture Meter to very many materials.

Designed for easy portability, fast operation with instantaneous indication and universal use. They are compact, handy units supplied with accessories, in a carrying case. Housed in a robust case, shaped to protect the large dial and controls. Power is supplied to the Aqua-Boy Moisture Meter by a 9 V battery.
>> Learn More | >> Request Information

WebAlert Remote Monitoring Device
Walchem's WebAlert is the first stand alone remote monitoring device that can web enable your installed equipment without having to replace or upgrade it. Your key system parameters (analog and digital) can now be monitored from any computer - anywhere in the world - with a standard web browser. 

WebAlert has an embedded webserver which allows it to function like a website.  And with Walchem's ShoulderTap Technology, the WebAlert is only on-line when you need it, making it the world's first practical and secure industrial monitoring Internet solution.
>> Learn More | >> Request Information

End Suction Centrifugal Pump Multi-Duti Advance 3000
The Advance 3000 was designed to meet the demand of low flow, high-pressure applications, while utilizing the compatibility of Noryl wetted parts. The enclosed impeller design ensures long life and durability. When used with the patented Impenatra Seal, the fluid does not contact any metal parts. This allows it to properly handle many applications at a fraction of the cost of exotic alloys. The Advance 3000 has multiple drain locations, allowing for several discharge orientations.

The Advance 3000 is a close coupled, unit end suction centrifugal pump line which is molded in Noryl. It's high efficiency design makes it suitable for medium flows (to-60 GPM) and higher heads (up to 160' TDH).
>> Learn More | >> Request Information

Corporation Stops From Primary Fluid Systems Inc.
Corporation Stops have been designed to inject chemicals into the center stream of the flow. An isolation valve allows for ease of maintenance.

Coproration Stops are available in 6 materials of construction. Wetted components have comparable or greater chemical resistance than quill construction material. Corporation Stops are available in standard and custom lengths. Connections are in NPT, Metric or flange.
>> Learn More | >> Request Information

Melt Pressure Gauges
Melt Pressure Gauges from ONEhalf20 are totally mechanical devices that offer ease of installation and maintenance. These melt pressure gauges are ideally suited to processors who require only visual indication of melt pressure.

Available in two unique styles. The CTG style features a 6" rigid stem and 30" of flex capillary. The RTG style has only a 6" rigid stem. Other configurations of these two styles are also available. In addition ONEhalf20 also offers these same mechanical gauges with 3.3 mV/Volt transducer output, or either 4-20mA or 0 - 10 Vdc transmitter outputs.
>> Learn More | >> Request Information

Extruder Rupture Disks
Extruder Rupture Disks (Burst Plugs) are designed to provide emergency pressure relief on plastics processing machinery.

Extruder Rupture Disks (Burst Plugs) are offered in a variety of lengths and configurations. Rupture disks are available with burst pressures from 1,500 up to 15,000 PSI. Offered with several mounting thread styles that are commonly found on plastics processing machinery. Designed exclusively for use on Plastics Extruders. The Extruder Rupture Disks (Burst Plugs) are designed to safely and effectively relieve built up pressure in a Plastic Extruder at a given pressure.
>> Learn More | >> Request Information

Ultrasonic Flow Measurement Granucor
A complete Granucor system is composed of two independent sensors and a correlator/ integrator. The DK13 Velocity Sensor and the DC13 Concentration Sensor operate using capacitance technology and are designed for direct installation into process piping. The concentration sensor measures the change in capacitance with material present versus the capacitance of an empty pipe. This change in capacitance is proportional to the material concentration.

The velocity sensor uses two measuring points and a technique known as cross-correlation to measure the time it takes for the material to travel between the points. The two-capacitance measurements are output to the MT2109 correlator/integrator, which calculates the mass flow rate.
>> Learn More | >> Request Information

Vortex Cabinet Coolers
Vortex Cabinet Coolers are an affordable, low maintenance, and easy to install alternative for thermal management of electrical cabinets and control panels. Using filtered compressed air and vortex tube technology, Vortex Coolers provide cooling capacities to 5000 BTUH and maintain NEMA 4, 4X and 12 ratings.

Today's small and compact, multi-function electronic controls, variable speed drives, servos and programmable logic controllers are extremely sensitive to heat and contamination. Excessive heat causes components to "cook", digital displays to misread, controls to drift, and breakers to trip below their rated loads. The result is often lost productivity from machine or line shutdowns.
>> Learn More | >> Request Information

Chemline SB Series Back Pressure/Relief Valves
SB Series Back Pressure/Relief Valves in solid plastics and stainless steel are now available from Chemline Plastics. They are designed for long maintenance-free life on chemical dosing lines ¼" to 4". They offer reliable opening and adjustable relief pressures of 3 to 150 psi. Advanced hydraulic design offers high flow rates, low hysteresis, and low overpressure to fully open.

All-plastic construction (PVC, PP or PVDF) offers high chemical resistance at
reasonable cost. True union end connections up to 2" eliminate leakage problems common with old-fashioned threaded body valves. The new "Chem-Flare" end connections provide a long term zero leakage solution for sodium hypochlorite services. SB17 is the compact model is for ¼" to ½" tubing, while the SB12 is available for pipe sizes ½" to 4".
>> Learn More | >> Request Information

Testing And Measurement Solutions
For over 40 years Intertechnology Inc., has been Canada's major distributor for Testing and Measurement Solutions. Located in Don Mills, Ontario we are proud to provide quick delivery of the very best technologies available.

Providing Canada With More Than The Product For Over 40 Years
...Means a commitment to serve clients with the best in measuring and testing technologies.
...Means maintaining Engineering, Applications and Service Support for the products we supply.
...Means maintaining up-to-date service and calibration equipment as well as a modern demonstration centre where our clients are invited to learn about stress analysis, related instrumentation and transducers.
...Means gauging services for clients - supplied components or we will manufacture a custom designed transducer to meet your requirements.
>> Learn More | >> Request Information

Process Controls And Instrumentation Advertising Opportunities
Your company can be a part of our web site with a Product Site with over 125,000 page views each and every month. Be a part of the Process News and reach over 52,000 readers worldwide every two weeks.

>> Learn More | >> Request Information