|
|
LevelSonic Ultrasonic Level Sensors
The small,
compact LevelSonic Ultrasonic Level Sensors offer non-contact measurement
of liquids and solid levels. The transmitter is two-wire loop-powered
and uses a simple magnetic key to set up the level range to be measured,
as well as selecting the response rate and default currents. On-board
AND visible operating and fault indication keeps you informed of the
operational and fault status at the transmitter.
The SONICTM is a cost effective, ultrasonic level transmitter
for measuring and monitoring liquid levels in open and closed tanks.
Its small size makes it supercompact, combining sensor and electronics
in one housing. The nose section is manufactured from Teflon. This Dupont
material is resistant to most chemicals, and includes an on-board, temperature
sensing element to ensure correct level measurement at all temperatures.
The electronics housing is manufactured from UPVC.
|
|
|
Stainless Steel Pressure Transmitters
Model PX61 Stainless
Steel Pressure Transmitters features compact construction, an integral
amplifier, 2-wire 4-20mA output signal and extensive medium compatablility.
Model PX61 design provides a 1/2% accurate, low cost pressure transmitter
that can operate over a wide temperature range with corrosion resistance.
Available from stock in both standard and refrigerant models.
|
|
|
seepex Progressive Cavity Pumps, Macerators and Control Systems
seepex progressive cavity
pumps, macerators and control systems are incorporated into a state-of-the-art
quality management system. With reliable quality and high-quality material,
the products meet utmost technical and qualitative customer demands.
The modular system is made up of 8 product groups and 27 ranges. Manifold
constructional designs facilitate purposeful adaptation to diverse operating
conditions of almost all branches of industry.
|
|
|
Minitwist Automatic Self Cleaning Filtration System
“Minitwist”
Model MTFC is a fully automatic, self-cleaning filtration system for
flows of 0 - 100 US GPM (23M3/H). It removes dirt as fine
as 20 micron, and uses a very small amount of water during cleaning
process. In filtration mode, flow is from bottom of filter to inside
of screen, and out. During cleaning mode, rotating nozzles collect dirt
removed from screen by reverse flow, and sends it out through top of
filter. Backwash process takes only 5 seconds.
|
|
|
NEW Nex FlowTM Air Products Corp. Catalog
Nex FlowTM
Air Products Corp., is a manufacturer of compressed air-operated products
made to improve plant efficiency, improve energy efficiency, improve
quality and enhance the environment. Our product line includes air blow-off
products that reduce air noise levels and compressed air use, and vortex
tubes technology using vortex tubes for spot cooling, control panel
cooling, tool cooling and other unique applications. It also includes
air operated conveying products and static control technology.
Nex FlowTM
Air Products Corp., introduces their new comprehensive catalog featuring
specialized compressed air technology products. This new catalog features
panel coolers, air knives, air wipes, air amplifiers, air nozzles and
jets, tool coolers, vortex tubes and spot coolers, safety air blowoff
guns, static eliminators, air operated conveyors, air optimization products
and industrial housekeeping and specialized products.
|
|
|
Microtrac Toroidal Conductivity Controller
The MICROtrac is a microprocessor
based feed and bleed toroidal conductivity controller designed to control
conductivity and feed inhibitor in cooling tower systems. Featuring
innovative toroidal sensor technology, the MICROtrac provides an economical
control platform that is not susceptible to sensor fouling and never
requires calibration! The MICROtrac measures the conductivity of the
cooling tower recirculating water via a toroidal conductivity sensor.
|
|
|
Accurate Flow Measurement from Outside a Pipe
This new portable ultrasonic
flowmeter is designed for clean liquids like water, glycol, oil and
most chemicals. Mount the clamp-on ultrasonic sensors on the outside
of plastic or metal pipes from 13-2000 mm diameter.
The PT500 Portable Transit Time Flowmeter is easy to calibrate with
a simple, step-by-step calibration menu. It displays and totalizes flow
and includes a built-in data logger, 4-20mA and pulse outputs. The PT500
is battery powered and packs away in a rugged, watertight carry case.
|
|
|
VortexAC Cabinet Panel Coolers For Electrical Enclosures
Avoid any downtime, with
the most affordable, reliable, and easiest to install thermal protection
product available for electrical enclosures!
Just as quiet as an air conditioner (about 62 dBA), the Vortex A/C noise
level is 93% less than other conventional, vortex type cabinet panel
coolers. When the thermo-statically-controlled Vortex A/C is operating,
the decibel level is about the same as normal human conversation!
This next generation, Vortex Cooler features an integral mechanical
thermostat to conserve energy and maintain enclosure temperatures within
a range of 80° to 90°F. Requiring only a compressed air supply
to operate, the UL listed Vortex A/C quickly installs in a 1.5”
knockout hole to keep electrical control panels cool, clean and protected.
|
|
|
1/16 DIN Digital Indicating Controller - Shinko ACS-13A Series
•
Compact, Space saving
• 11-segment LCD display
• An easier viewing display PV color switchable
• Standard console connector equipped
• Standard Output rate of change limit
• Multi-input ºC
• High-speed sampling
• Multiple options
Set value memory external selection
Serial communication
Heater burnout alarm output
Heating/Cooling control output
|
|
|
Liquid Level Float Switches
Liquid Level Float Switches
from Ktech Industrial Products Inc., Are top-mounted with between one
and four setpoints. A single point sensor may be used to provide a high
or low level alarm contact.
Liquid Level Float Switches
are factory-sealed and explosion-proof. They are approved for hazardous
locations, Class 1, Division 1, Groups B, C, D. Explosion-proof housings
are an optional accessory.
|
|
|
Belt Type Oil Skimmers
Mini-skimmers have been
in use throughout the world since 1990. Thousands are used daily to
remove unwanted floating "tramp" oils.
They are small, run very
quietly, and use a very dependable permanent magnet motor! Standard
models for industrial users include oil pickup rate to 1 gallon/hour,
loose or fixed tail pulley design, and a choice of polyurethane (for
coolants & oil/water) or stainless steel(for parts washing) belts
in four standard length sizes.
Special skimmers with
other options such as special belt lengths (to 100 ft.), two belts,
stainless motor covers, etc. are available.
|
|
|
Plastic Ultra-Low Flow Meters - EM Series
The Chemline
EM Series Electromagnetic flow meter is a full port small diameter design
for low flows. It accurately measures pulsating flows from diaphragm
type chemical metering pumps. Successful applications in the waste/water
industry include sodium hypochlorite, ferric chloride and flocculating
agents. The flow tube is solid PVDF with platinum coated titanium electrodes.
Available
control outputs include pulse, 4 – 20 mA and an LCD display for
flow rate and total flow plus high and low flow alarm relays. EM Series
meters do not need to be recalibrated every time a new chemical is added
to the injection process. These units offer the same high accuracy and
reliability as equivalent metal alloy meters at lower cost.
|
|
|
Nex FlowTM X-StreamTM
Air BladeTM Air Knife
Nex FlowTM
Silent X-StreamTM Air BladeTM Air Knife is highly
efficient and quiet, Easy to mount and maintenance free. Replaces drilled
pipe or rows of nozzles and jets with compressed air savings up to 50%.
Unlike most competitors they have a stainless steel shim (no plastic)
to maintain a small gap for compressed air that exits and entrains surrounding
air to “amplify” air flow. This produces a narrow curtain
of air flow for blow-off and cooling. Air inlets at ends or back with
convenient mounting holes. In addition to the stainless steel shim,
the aluminum unit is gold anodized for long life. All stainless steel
units are available for high temperature and food applications. Compact
and sleek design for tight areas and high efficiency operation.
|
|
|
Melt Pressure Gauges
Melt Pressure Gauges
from ONEhalf20 are totally mechanical devices that offer ease
of installation and maintenance. These melt pressure gauges are ideally
suited to processors who require only visual indication of melt pressure.
Melt Pressure Gauges from ONEhalf20 are available in two unique
styles. The CTG style features a 6" rigid stem and 30" of
flex capillary. The RTG style has only a 6" rigid stem. Other configurations
of these two styles are also available. In addition ONEhalf20
also offers these same mechanical gauges with 3.3 mV/Volt transducer
output, or either 4-20mA or 0 - 10 Vdc transmitter outputs. These unique
gauges feature the standard Bendix style 6 pin bayonet connector and
are ideal for processors looking for localized visual indication at
the extruder barrel.
|
|
|
Arctic Bag Filter Housings
Pelmar Engineering offers
a complete line of Arctic Bag Filter Housings to fulfill all your bag
filtration needs. Our Bag Filter Housings are manufactured in a strict
quality controlled environment. The designs are based on many years
of industrial experience and provide maximum efficiency and reliability.
The line includes both Over The Top (OT) and side Entry (SE) designs,
four sizes P1 through P4 and three materials Carbon Steel, 304SS and
316SS.
|
|
|
Thin Film Pressure Transducers Ashcroft Model K1
Thin Film Pressure Transducers
Ashcroft Model K1 transmitter introduces the benefits of polysilicon
thin film performance at affordable prices. Modern low-pressure chemical
vapor deposition methods provide simple, stable molecular bonds between
a proven metal diaphragm and a polysilicon strain gage bridge. There
are no epoxies or bonding agents to contribute to signal instability
or drift.
The polysilicon strain resistors combine very low noise levels with
very high signal output. There are no semiconductor (p-n) junctions
to change with temperature, time or use. The integral metal diaphragm
and polysilicon bridge are virtually unaffected by shock, vibration
or mounting position.
|
|
|
Drum Heaters
Drum Heaters
are a used to control temperatures on a variety of pails or drums where
maintaining viscosity and keeping the contents fluid are important.
Drum Heaters provide uniform heat and prevent scorching or degradation
of sensitive materials.
Drum Heaters also provide freeze protection and are available with fixed
or adjustable thermostats for various applications. Common voltages
and sizes are available from stock but custom designs can be manufactured
to suit your application. Also see our Explosion Proof Drum Heaters.
|
|
|
Process Controls And Instrumentation Advertising Opportunities
Your company can be a
part of our web site with a Product Site with over 125,000 page views
each and every month. Be a part of the Process News and reach over 52,000
readers worldwide every two weeks.
|
