|
|
Gas Leak Detectors
Gas detector Peaker 3000 flex is a multi range gas detector, which is equipped with a selective gas sensor series GGS 3000 for methane (CH4), but is also suitable for the detection of propane gas (C3H8) und hydrogen (H2). The detection range is from a few ppm up to the “Lower Explosive Limit (LEL)”, which are stored for the different gases in the micro processor and can be called off. Leak detection for the different gases is carried out with a single sensor. Gas detector Peaker 3000 flex is not designed to be a measuring device. Peaker is a gas leak detector and should not be used a personal protection instrument!
|
|
|
Stingray Portable Open Channel Flow Logger
A portable logger for area-velocity flow surveys in sewers, open pipes and channels. Stingray is designed for stormwater, sewage, wastewater, irrigation water and stream flow. Stingray uses a submerged ultrasonic sensor to measure both Velocity and Level in the channel. No calibration is required. It operates up to 4 years powered by standard Alkaline batteries and includes Greyline Logger software to retrieve and display logged data by RS232 or modem connection. The software calculates flow for round, rectangular, trapezoid and egg shaped channels plus flumes and weirs.
|
|
|
WebMaster® Industrial (WIND) Controller
Walchem's WebMaster® Industrial (WIND) Controller sets a new standard for Industrial Water treatmentControllers. The WIND has a flexible multi-I/O platform, a wide rangeof analytical sensor measurement capabilities, and an extensive assortmentof integrated communications and data handling features.
|
|
|
Extruder Rupture Disks
ONEhalf20
Extruder Rupture Disks
(Burst Plugs) are designed to provide emergency pressure relief on plastics processing machinery. Offered in a variety of lengths and configurations. Rupture disks are available with burst pressures from 1,500 up to 15,000 PSI.
ONEhalf20
Extruder Rupture Disks (Burst Plugs) are offered with several mounting thread styles that are commonly found on plastics processing machinery.
|
|
|
Nex FlowTM Frigid-XTM Panel Coolers
Nex FlowTM Frigid-XTM vortex tube panel coolers not only have major advantages over other cooling options but also over many other systems using vortex tubes. A vortex tube operates using compressed air only, dividing up the air into a hot and a cold stream with no moving parts. The cold air flow produced is used is directed into the enclosure to air condition the control cabinet.
The Frigid-XTM panel coolers has a built-in exhaust to vent the displaced hot air from inside the enclosure, so no separate vent is needed. This creates a slightly positive pressure inside the cabinet to purge the unit and keep out dirt, dust and debris.
|
|
|
Ultrapen - PT1
The Ultrapen - PT1 is designed to be extremely accurate, fast and simple to use in diverse water quality applications. Advanced features include the ability to select from 3 different solution types that model the characteristics of the most commonly encountered types of water; proprietary temperature compensation and TDS conversion algorithms; highly stable microprocessor-based circuitry; user-intuitive design; and waterproof housing. A true, one-handed instrument, the PT1 is easy to calibrate and easy to use. To take a measurement, you simply press a button then dip the pen in solution. Results display in seconds.
>>Learn More
>>Request Information
>>Vendor's Product Last Issue
|
|
|
Personal Cooling/Heating System
Personal Air Conditioners were created to keep workers wearing protective clothing comfortable in extremely hot or cold working conditions. The Vortex Tube powered personal air conditioners use compressed air at 70-100 PSIG to produce cold or warm air to heat or cool a worker in protective suite. Temperature range from 60 F cooler or hotter than the inlet can be achieved.
Applications:
Unlike "ice pack" type vests, the Personal Air Conditioners (PACs) offers consistent and continuous cooling to minimize heat stress and increase worker productivity in hot surroundings. The vest allows full range of motion with no airflow restrictions and can be worn under welding leathers or protective clothing. The vortex tube unit, worn on a supplied belt, cools or heats inlet temperature by ±60°F.
|
|
|
CS Corporation Stops
CS Corporation Stops have been designed to inject chemical into the center stream of the flow. Available in 7 materials of construction: brass, PVC, CPVC, PVDF, Stainless Steel, Alloy 20 and Hastelloy. Quill diameter sizes range from 1/4" (DN 8) to 2-1/2" (DN 65). They are available in the following sizes 1/2" (DN 15) to 3" (DN 75) with threated, socket or flanged connections.
|
|
|
Exner Characterized Control Valves
The Chemline Exner Characterized Control Valves provide extremely precise flow control of aggressive fluids. Valves flow characteristics (Cv vs. lift) follow theoretical linear or equal percentage curves through the entire range of stem travel. This is accomplished with precision made replaceable seats and plugs in a wide variety of Cv values.
- Precise & Sensitive Control
- Changeable Plugs & Seats
- Low Maintenance
|
|
|
Vortex Tubes – a unique spot cooling device using no electricity
The vortex tube is unique technology that takes compressed air divides it into two flows - one end of the tube gets hot and the other tube gets cold. It was a little known technology 30 years ago but now is commonly used in several types of useful devices.
Compressed air, typically at 80-to 100 PSlG enters the vortex tube from the side at a tangent and enters through the generator into the tube, causing the air to spin. This air stream spins toward the hot end where some leaves the tube via the control valve. The remaining, spinning air travels back up the center of the tube. The inner spinning stream gives off heat energy to the outer stream (which leaves the tube at the hot end as hot air) and exits the vortex tube at the cold end as cooled air. The input air is literally split into hot and cold and can be quite extreme in range.
|
|
|
Static Weighing With Ramsey Micro-Tech 3000 Series
The Ramsey Micro-Tech 3000 Series of electronic instruments signifies a new approach to scale instrumentation, giving you more flexibility and vastly increased upgrade capabilities. Each model is designed for your specific weighing application, and because all models utilize a common platform, you only need to become familiar with one basic interface.
|
|
|
NEW STREAM VACTM Dust Collection and Fume Extraction System
The Model 40002FMS STREAM VACTM is a versatile and affordable compact air cleaning system is ideal for the removal of fumes, dust and other air pollution from work stations without the need for heavy and bulky machinery. The Nex FlowTM Stream VacTM is an in line air conveyor that when hooked up to a 2” hose up to 25 feet (8 meters) and connected to a compressed air line, it will remove up to several hundred cubic feet of air while using only a minimal amount of compressed air, taking with it welding fumes, soldering fumes, particulate from local grinding operations, smoke and particulate from almost any “spot” application.
|
|
|
Martel MC-1010 Multi-Function Process Calibrator
The Martel MC-1010 multi-function process calibrator will test continuity as well as read and source thermocouples, RTDs, Ohms, voltage, current, and frequency. The unit is compatible with BetaPort-P and Fluke 700 series pressure modules which expand its range to pressure applications. Results are shown of the high contrast ClearBrite graphic display which features a vivid white backlight that makes the display easy to read in all light conditions. Martel's easy to learn yet powerful 3 key menu structure provides a highly intuitive yet powerful operator interface. Learn more about all the Mat\rtel (Beta) line of calibrators.
|
|
|
Load Cell Summing Transmitter Sensortronics Model 2520
Load Cell Summing Transmitter Sensortronics Model 2520 is used for precision weighing with load cells, process control add-on loops applications and can be used with all types of low output sensors.
Load Cell Summing Transmitter Sensortronics Model 2520 features summing of up to 4 load cells, complete strain gauge bridge signal conditioner, high gain, low drift, low temperature coefficient precision amplifiers with low input current (10 pA typical).
|
|
|
Process Controls And Instrumentation Advertising Opportunities
Your company can be a part of our web site with a Product Site with over 125,000 page views each and every month. Be a part of the Process News and reach over 52,000 readers worldwide every two weeks.
|
|
|
Process Controls And Instrumentation News Is Now On Facebook
Process Controls and Instrumentation is now on Facebook showing product links to the worlds leading manufacturers and suppliers of process control and instrumentation equipment. Be sure to click on the Like Button on the page.
|
