January 26, 2016  
www.process-news.com   

Process News Web Site  | Advertising Opportunities | Add Me | Remove Me | Products | Library | View Newsletter Online

PTF06 Series Pressure Transmitters

PTF06 Series Pressure Transmitters are very accurate and reliable instruments, which convert pressure inputs to current or voltage signals. These transmitters are equipped with a damping element to direct away pressure peaks or liquid hammering from their sensors; hence showing a high level of resistance to mechanical shocks. The typical response time of the PTF06 transmitter is 1 ms, and will never exceed 5 ms, even when the damping element is functioning and the fluid viscosity is at its peak.

The industrial PTF106 Pressure Transmitter meets the electromagnetic compatibility (EMC) requirements of IEC61000-6-2 and IEC61000-6-3.

<< Learn More >> << Another HCS Product >>


DFS 5.1 Doppler Flow Switch

Control Flow from outside a pipe. Recommended for "difficult liquids" including wastewater, cooling water, slurries, sludge, chemicals, viscous liquids and abrasives. The Greyline DFS 5.1 is ideal for pump protection or to activate flow/no-flow alarms.

The DFS 5.1 control relay can be set to turn ON and OFF at any flow rate between 0.25 and 10 ft/sec (0.075 to 3 m/sec). Insert two links for separate ON/OFF set points or just one link for a Hi or Lo flow alarm. Set the relay actuation time delay from 0 to 80 seconds.


CHEM-PRO C2 ProSeries Diaphragm Pump

  • Max feed rate: 15 GPH / 55 LPH
  • Max pressure: 175 PSI / 12 bar
  • 166 RPM (Max strokes per minute)
  • Variable speed, Smooth motor driven chemical feed
  • Nema 4X washdown / IP 66
  • Back Lit LCD display
  • Priming / Degassing Valve – Built-in
  • Leak Detection – Built-in Diaphragm Failure Detection (DFD)
  • Exclusive Diaflex® Single Layer PVDF diaphragm.

3 Inch Air-Blade™ Air Knife Blow Off System

The 3 Inch Air-Blade™ Air Knife Model 10003 Blow Off System from Nex Flow™ is easy to mount and maintain and reduces both compressed air consumption and noise levels.

The 3 Inch Stainless Steel Air-Blade™ Air Knife Model 10003S Blow Off System from Nex Flow™ produces a “laminar” flow of air along its length using the ”Coanda” effect which “entrains” a large volume of air from the surrounding area along with the small amount of compressed air from the Air-Blade™ to produce an output flow up to 30 times.

Air-Blade™ Air Knife Blow Off System payback on compressed air savings can be as soon as a few weeks in some applications.

Nex Flow™ Mounting Systems for air knives and air amplifiers provide a convenient and flexible way to utilize the products for blow-off and cooling applications.


Carlon Water Meters

When long meter life, low maintenance and highest accuracy are needed in a totalizing water meter, Carlon's Residential & Commercial line of positive displacement meters are what you need. The Residential & Commercial line has a well deserved reputation for excellence in the world of municipal and residential water meters.

The Residential & Commercial meter is available in sizes from 1/2" to 2" and operates at flow rates from 1/4 to 160 GPM and pressures of 150 psi. These ratings are well beyond what you will encounter for your municipal and residential metering needs. All of Carlon's bronze housing Residential & Commerical meters meet or exceed AWWA specifications.


CS Corporation Stops

CS Corporation Stops have been designed to inject chemical into the center stream of the flow. Available in 7 materials of construction: brass, PVC, CPVC, PVDF, Stainless Steel, Alloy 20 and Hastelloy.

Quill diameter sizes range from 1/4" (DN 8) to 2-1/2" (DN 65). They are available in the following sizes 1/2" (DN 15) to 3" (DN 75) with threated, socket or flanged connections.


High Temperature Air Wipe

1" Stainless Steel High Temperature Air Wipe Nex Flow™ X-Stream™ Ring-Blade™ Air Blow-Off System Model 20001XS-316L is designed for high temperatures up to 800ºF (427ºC) and corrosive environments is easy to mount and maintain and reduces both compressed air consumption and noise levels.

1" Stainless Steel High Temperature Air Wipe Nex Flow™ X-Stream™ Ring-Blade™ Air Blow-Off System Model 20001XS-316L produces a “laminar” flow of air along its 360º angle using the “Coanda” effect which “entrains” a large volume of air from the surrounding area along with the small amount of compressed air from the Ring-Blade™ air-saver wiper-blade to produce an output flow up to 30 times.

1" Stainless Steel High Temperature Air Wipe Nex Flow™ X-Stream™ Ring-Blade™ Air Blow-Off System Model 20001XS-316L pay back on compressed air savings can be as soon as a few weeks in some applications when compared to nozzle “rings” or simple annular slots used by other air wiping systems.


IP258 Pressure Indicator from ONEhalf20

The ONEhalf20 IP258 Pressure Indicator with strain gauge input and dual 5 digit display features high accuracy and simplicity of operation. The IP258 is available with up to three programmable alarms, 4-20mA or 0-10Vdc process value re-transmission, and MODbus communications.

The IP258 Pressure Indicator offers simplified user functionality with front panel buttons for Zero, Peak, and Manual Alarm Reset. The IP258 Pressure Indicator is a compact 1/8 DIN (96 x 48 mm) package with a large 0.5 inch LED display for process pressure indication.


Split Core Current Sensors

Split Core Current Sensors Model SC225 is our easiest to install fixed setpoint current operated solid state status sensor for status indication.

The one unit is pre-set to switch at 1.5 amps and will switch either AC or DC loads. This flexible design eliminates installation problems. It is not possible to incorrectly set the trip point or install a DC unit when an AC load should be switched.

Split Core Current Sensors Model SC225 design means that retrofit installations are simplified since power does not have to be shut off and connections do not have to be broken.


ITMA or V Industrial Pressure Transmitters

The ITMA or V Industrial Pressure Transmitters are designed for the tough environments of hydraulic applications with the possible prescence of corrosive materials.

The ITMA or V Industrial Pressure Transmitters feature the reliable Bendix style 6 pin connector and either 4-20mA or 0 - 10 Vdc output. The units offer 1/8 X 27 NPT female process connection as standard.

  • 4-20mA or 0 - 10 Vdc outputs with zero and span adjustments
  • Accuracy +/- 0.5%
  • Internal 80% shunt calibration
  • All welded all stainless steel construction

Vortex Tubes

There are three basic physical sizes of vortex tubes used extensively in industry the version, medium version and large version. Vortex tubes can be selected by required performance in cooling for the "H" generator versions and where very cold temperatures are required "C" generators are used. However, even with "C" generators, as expected, the higher the flow rating the greater the cooling effect.

Nex Flow™ stainless steel vortex tubes use a metal (brass) generator as a standard item rather than cheap plastic for longer life and for applications in high temperature environments. (competitors would charge extra for that feature.) With virtually no moving parts, Vortex Tubes take compressed air and converts it to cold air at one end and hot air at the other. Temperature as low as -50ºF (-46ºC) can be achieved at the cold end and up to 260º F (127ºC) at the hot end.

Vortex tubes are used to cool electronic controls, machining operations, spot cooling and more.


Ramsey RT Series Rotary Level Control

The Ramsey RT Series Rotary Level Control is designed for point level monitoring of solids in bins, vessels and chutes. This control can eliminate spills, material waste and down time by preventing bin overflows, plugged chutes and empty bins. It works equally well with plastics, food, chemicals, raw ores, aggregates or other solid materials.

Thermo Fisher Scientific's RT Series Rotary Level Control is designed for Point Level Monitoring of solids in bins, vessels and chutes.  The RT Series Rotary Level Control can eliminate spills, material waste and down time by preventing bin overflows, detecting plugged chutes and empty bins.  The RT Series Rotary Level Control for Point Level Monitoring works equally well in plastics, food, chemicals, raw ores, aggregate or other solid materials.


Miniature Cable Extension Position Transducers

The MTA is part of Celesco’s miniature line of cable-extension position transducers that is perfect for short ranged testing and control applications where space is at a premium. This transducer uses a high-cyle conductive plastic potentiometer to provide a precision voltage divider feedback signal for measurement ranges of 3 or 5 inches full stroke.

With an accuracy of ±0.4% and a repeatability of ±0.02%, the MTA conveniently mounts using servo-clips for easy rotational adjustment.


Process Controls And Instrumentation

We've added a Glossary Of Terminology section, a What's New In Process Controls section, and a Product Video Library section. As well we have updated our Buyers Guide and Company Directory to make it easier to find the products and manufacturers you are looking for.

This news letter from Process News is sent to those who wish to be kept informed of new products via email.

<< Learn More >>