|
Week
Of May 22, 2007
|
 |
|
Immersion
Heaters |
Flanged
Immersion Heaters are used in large capacity vessels, for high temperature
and pressure applications. They
are installed by bolting the unit to a matching flange welded to the
vessel. Watt densities from 90 Watts/sq inch, Explosion Proof (NEMA
7), Corrosion Resistant (NEMA 4X), General Purpose and Standoff Terminal
housings are available. A number of sheath materials like Titanium,
Incoloy, Stainless Steel, Steel, and Copper can be used as required
for specific applications. |
|
Current Transducers Sentry 100 Series are used to monitor motors, pumps, conveyors, machine tools and any electrical load where an analogue representation is required over a range of currents. Current Transducer Solid Core Sentry 100 Series models are CSA approved and UL listed. Sentry 100 Series comprises a current transformer, range selector, rectifier-filter, and scaling circuit. Each sensor has three basic user selectable ranges. The 0-5 VDC output is available on two 6-32 screw terminals. |
Solid
Core Current Transducers with 0-5V output.
Sentry 100 Series convert a monitored AC current to a proportional
DC voltage of 0 to 5 Volts. |
|
Portable
Doppler Flowmeter
The EESIFLO EASZ-10P is a handheld non-invasive microprocessor
based meter for measuring the flow rate and total volume of liquids
flowing through process and effluent pipelines. It is suitable for a
wide range of liquids, including aerated water, liquids containing suspended
solids, slurries and sludges. The EESIFLO EASZ-10P requires fluids with
a minimum concentration of 100 ppm of solids or bubbles having minimum
size of 100 microns and works on most pipes 2 inches and above.The flowmeter utilises the non-intrusive Doppler principle to measure the mean velocity and is particularly useful as a temporary flow indicator or as a working tool to establish flow conditions in field or plant installations. Units of measurement available are m/s, ls, lm, lh, m3/sec, m3/m, m3/hr, ft3/h, ft3/s, usgps, usgpm, usgph, usmgd. See Complete Product Information | Request More Information |
|
|
Water Treatment Controller
|
The
Model 1575e uses the latest in microprocessor capability, giving the
user a high level of application flexibility. A large illuminated
graphics screen, multiple inputs, and very easy setup characterize
this new technology. The Model 1575e is UL/CSA/CE approved. |
|
EchoSwitch Multi-Point Ultrasonic Level Switch From Flowline |
The
general purpose ultrasonic level switch provides non-contact level
detection up to 40' or 12.2m with 3 relays and 1-6 set points.
Each relay can be configured on a single set point alarm, two
latched set points for automatic fill or empty control or two
independent set points for out of bounds alarming. |
|
This general
purpose liquid or gas switch package provides a low flow detection
solution for pump or process protection with a 1A relay interface
for remote devices such as a PLC, SCADA or alarm. The short sensor
is intended for use in pipe or ducting from 1/2" to 11/2"; the
long sensor is applied in 2" and up. The product is broadly selected
for low or no-flow applications. Specify the appropriate sensor
technology, length and material. |
Switch-Pro
Flow Switch with Compact Relay Controller From Flowline |
|
Liquid
Level Float Switches from Ktech Industrial Products Inc. Liquid Level Float Switches are factory-sealed and explosion-proof. They are approved for hazardous locations, Class 1, Division 1, Groups B, C, D. Explosion-proof housings are an optional accessory. |
|
|
"Minitwist"
- MTFC - Automatic Self-Cleaning Filtration System  “Minitwist”
Model MTFC is a fully automatic, self-cleaning filtration system for
flows of 0 - 100 US GPM (23M3/H). It removes dirt as fine as 20 micron,
and uses a very small amount of water during cleaning process. In filtration
mode, flow is from bottomof filter to inside of screen, and out. During
cleaning mode, rotating nozzles collect dirt removed from screen by
reverse flow, and sends it out through top of filter. Backwash process
takes only 5 seconds.• Fully automatic filtration system • Self cleaning, using system water only • Corrosion resistance materials • Easy to install. Inlet, Outlet and Drain • It takes only 5 seconds for backwash • Quick opening clamp for inspection • Virtually maintenance free See Complete Product Information | Request More Information |
|
|
Extruder
Rupture Disks  Extruder Rupture Disks are designed for reliable emergency relief of excess pressure since they instantaneously rupture at a specific predetermined pressure range.
Skylark Controls model CBP Extruder Rupture Disk is designed specifically for use in plastic extruders. Each assembly consists of a stainless steel body and rupture disk. A rupture disk may be specified for primary relief in applications where pressure buildup can occur so rapidly that the response time of a relief valve is inadequate, such as in a polymerization reaction vessel.See Complete Product Information | Request More Information |
|
|
Back Pressure/Relief Valves for Chemical Dosing  SB
Series Back Pressure/Relief Valves in solid plastics and stainless steel
are now available from Chemline Plastics. They are designed for long
maintenance-free life on chemical dosing lines ¼” to 4”.
They offer reliable opening and adjustable relief pressures of 3 to
150 psi. Advanced hydraulic design offers high flow rates, low hysteresis,
and low overpressure to fully open. All-plastic construction (PVC, PP
or PVDF) offers high chemical resistance at reasonable cost. True union
end connections up to 2” eliminate leakage problems common with
old-fashioned threaded body valves. The new “Chem-Flare” end connections provide a long term zero leakage solution for sodium hypochlorite services. SB17 is the compact model is for ¼” to ½” tubing, while the SB12 is available for pipe sizes ½” to 4”. The same valve offers both as both back pressure and relief functions. For relief the valve is installed on the branch of a tee. See Complete Product Information | Request More Information |
|
| Continuous
Duty Rocking Piston Diaphram Air Pump
|
The
TUF Pump is a 1/20 horsepower, continuous duty, rocking piston diaphragm
air pump for use in pressure or vacuum applications. Its sealed bearings
motor requires no lubrication. It can be used as an air supply for bubbler
type liquid level controls requiring constant 24/7 operation. |
|
|
New
Solids Transfer Pump From Australia Does What No Other Pump Can! |
|
Melt Pressure Gauges
|
Melt
Pressure Gauges from ONEhalf20 are totally mechanical devices. They
offer ease of installation and maintenance. In addition these gauges
are ideally suited to processors who require only visual indication
of melt pressure. |
|
Screwplug Heaters from Wattco
|
