Week Of October 23, 2007

Process Controller - FUZYPRO 6100 1/16 DIN

With its improved interface, technical functionality and field flexibility, the FUZYPRO 6100 gives you the best in comprehensive control for most temperature and process control loops. Full PID with Pre-tune, Self-tune, manual tuning, or On-Off control. Heat only or heat & cool. Selectable from front panel or via digital input, with bumpless transfer. Up to 3 possible, for control, alarm, 24VDC transmitter power supply or retransmit of process value or setpoint. Process high, process low, SP deviation, band, logical OR / AND. Also 1 loop alarm for process control security. Process alarms have adjustable hysteresis. 4 button operation, dual 4 digit 10mm & 8mm high LED displays, optional choice of colours (Red/Red, Red/Green, Green/Red or Green/Green), plus 5 LED indicators.

Wireless CellMite Model 4329 Digital Signal Conditioner

CellMite® Model 4329 Signal Conditioner features a nonvolatile memory for parameter and calibration storage, the ability to select between three transducers, multi-point and mV/V calibration, remote sense excitation, and a 24-bit internal resolution with 16-bit analog output.

CellMite® compensates for transducer nonlinearities using its integrated 6-point calibration. Its wireless communication port and simple command set allow connection of up to 8 units in a wireless serial network configuration.

  • Model 4329 connects directly to a standard strain gage, load cell, extensometer, or pressure transducer.
  • Wireless communication to 1500 feet.
  • Simplified distributed process measurments.
  • Din Rail mount available.

See Complete Product Information | Request More Information
       

General Purpose Level Switch

The LS6000 is a basic, general-purpose level switch that can measure virtually any liquid, dry material or interface of electrically conductive or non-conductive products. The proprietary radio frequency (RF) balanced impedence bridge has exceptional temperature stability, thus eliminating the need to recalibrate the unit from season to season.

When the probe is installed, it is calibrated in absence of material touching the probe. When the desired material comes in contact with the probe, the LS6000 is activated and gives the desired output.

See Complete Product Information | Request More Information
   

Voltage To Resistance Transducer

The ETR accepts a generic Analog Output signal (voltage or current) and provides variable resistance output as a simulated potentiometer. The board performs 64 step approximation with about 1.5% output resolution. For high output accuracy the ETR's resistive array utilizes a number of 1% precision metal film resistors. Their unique configuration allows for over 4 Watts power dissipation.

The ETR is equipped with a Local Override feature that allows for manual output control. Output status is indicated by 6 LEDs in an easy to follow binary code. The input current loop, the Local Override mode and the processor status are also indicated by LEDs.

Electrically Actuated True Union Ball Valves Hayward Series EA

Low Cost Automation: The EA electrically actuated true union ball valve is the perfect answer to cost sensitive, automated valve applications that can't get by with less than a full featured valve and actuator combination. Other low cost automated valves use a stripped down actuator with a non-repairable, "throw-a-way" type valve. The EA features a fully serviceable true union ball valve for long reliable service.

Corrosion Resistant Valve: The all plastic construction of the EA true union ball valve means that there will never be a problem with rust or corrosion. The valve will never stick, jam or fail to operate like a metal valve might because of corrosion.

Built to Last: The EA Series valves feature a rugged 110 VAC electric actuator with an output torque of 140 in. lbs. A built-in, automatic resetting thermal overload protector prevents motor burnout. The 25% duty cycle motor drives the valve through a permanently lubricated, rugged gear train. There is never a need to set, adjust or fool with internal actuator adjustments, which are set for the life of the actuator when it is built. All internal components are sealed inside a rugged, all plastic Nema 4X housing.

See Complete Product Information | Request More Information
       

Hayward - Simplex Plastic Basket Strainers

When pipeline system components require protection from dirt and debris and the line can be shut down for basket cleaning, a HAYWARD® All Plastic Simplex Basket Strainer is the ideal choice. Unwanted particles are removed as the process media passes through a perforated strainer basket contained inside the strainer body. The basket traps the unwanted material while allowing the process media to flow freely.

Changing or cleaning the strainer basket is quick and easy. The hand removable, spin-off cover features two angled handles for easy access to the strainer basket. The housing features external cover threads that do not contact the process media and never need cleaning. Venting and draining are made possible by two hand removable, threaded plugs, one on the top of the cover and the other on the housing side.

See Complete Product Information | Request More Information
    

Pump Controllers from Ktech Industrial Products Inc.

Pump Controllers are installed to automatically operate a pump to control the level of a liquid in a tank. They are used in conjunction with Ktech Multi-Level Float Switches. Use two contacts to start and stop the pump. A relay circuit switches power to the fractional horsepower pump motor or to the three-phase contactor of a large pump motor.

Similarly, the switch contacts can be used to operate solenoid valves. Use additional contacts to indicate an alarm condition. These alarms provide an audible and visual signal. The audible signal can be muted after which the warning light remains on until the alarm condition is corrected.

See Complete Product Information | Request More Information
   

Arctic Bag Filter Housings

Pelmar Engineering offers a complete line of Arctic Bag Filter Housings to fulfill all your bag filtration needs. Our Bag Filter Housings are manufactured in a strict quality controlled environment. The designs are based on many years of industrial experience and provide maximum efficiency and reliability. The line includes both Over The Top (OT) and side Entry (SE) designs, four sizes P1 through P4 and three materials Carbon Steel, 304SS and 316SS.

  • Large inventory in stock at all times
  • 120, 150, and 300 psi Standard Models
  • Swing bolt closures allow easy access (P1 and P2)
  • Secure bag seal to prevent by-pass
  • 316 stainless steel retainer basket
See Complete Product Information | Request More Information
   

Extruder Rupture Disks

ONEhalf20 Extruder Rupture Disks (Burst Plugs) are designed to provide emergency pressure relief on plastics processing machinery.

Extruder Rupture Disks (Burst Plugs) from ONEhalf20 are offered in a variety of lengths and configurations. Rupture disks are available with burst pressures from 1,500 up to 15,000 PSI.

ONEhalf20 Extruder Rupture Disks (Burst Plugs) are offered with several mounting thread styles that are commonly found on plastics processing machinery.
See Complete Product Information | Request More Information
   

Melt Pressure Transducers

Melt Pressure Transducers offer high accuracy, repeatability, industry standard functionality, at prices substantially below the competitors.

Features:

  • Global Leader in price/performance, quality, and delivery
  • 6 Pin Bayonet Connector – Industry Standard Design – Compatible Color Coding
  • 80% Output Calibration – Industry Standard
  • Fully interchangeable with competitors models without re-wiring – 100% Field Compatibility
  • General Purpose Grade Featuring .5% accuracy

See Complete Product Information | Request More Information
       

Low Cost Ultrasonic Sensors

Massa Products introduces the M-300 Family of RoHS compliant Ultrasonic Sensors that incorporate state-of-the-art ultrasonics and microprocessor technology to provide low cost precision non-contact distance measurement for factory automation or industrial process control. The M-300 Sensors stand out over all other systems because of their affordability while providing extraordinary ease of operation, genuinely user-friendly software, versatility in user-controlled outputs, narrow beam sound pulses at user-selected rate (or it can be software triggered), processes return echoes, and produces several outputs dependent on the position of the target.

Operating from 12 to 24 VDC, the M-300 Family includes several sensor models that operate at different ultrasonic frequencies, which produce detection ranges from as close as 4 inches (100 mm) to greater than 15 feet (4.5 meters). A linear output of 0 to 10 VDC is provided, which is proportional to the measured distance to the target from the minimum detection distance to the nominal maximum target distance specified for the particular M-300 model.

See Complete Product Information | Request More Information
    

Capacitance Level Control

Thermo Electron Corporation's "CAP" Series Capacitance Level Control is designed for point level monitoring of solids, fluids or slurries in bins, vessels and chutes. The CAP Capacitance Level Control can eliminate spills, material waste, and down time by preventing bin overflows, plugged chutes and empty bins. The CAP Capacitance Level Control works equally well as a high or low level indicator in plastics, food, chemicals, mineral slurries, or other materials.

CAP Capacitance Level Control detects the presence or absence of material by sensing a change in capacitance caused by the difference in dielectric constant of the vessel material and air. To detect these small changes, the CAP series sensors use a unique detection circuit that operates at a relatively low frequency level (6 KHz). Unlike other capacitance sensors, the operating frequency of the CAP Capacitance Level Control series is well below the RF level and not subject to FCC regulation.

See Complete Product Information | Request More Information
       

Plastic Butterfly Valves

The Chemline Type 57 is the new updated version of the Type 56 Series. The redesigned hand lever no longer has external metal parts. The Type 57 has a redesigned valve "top flange" and shaft, now conforming to ISO for standardized actuator mounting*. These valves offer a large range of sizes and selection of body, disc and seat materials. This allows them into a wide range of on/off or throttling control applications.

The Chemline DBF Series FRP Damper Butterfly is manufactured by Canada’s foremost fabricator of engineered FRP gas and liquid handling equipment. They have manufactured FRP dampers for demanding process applications since 1967. This is a quality engineered valve designed for corrosive and/or abrasive gasses in FRP large diameter duct systems.

See Complete Product Information | Request More Information